|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
INTERNATIONAL METAL
ENGINEERING |
|
|
|
|
|
|
|
|
|
FIELD MOUNTED 2 WIRE
SMART TRANSMITTER |
|
|
|
8080TR |
|
|
|
n |
INPUTS: THERMOCOUPLE,
RTD, OHM AND MV |
|
|
|
|
|
n |
HIGH ACCURACY |
|
|
|
|
|
|
|
|
|
|
|
n |
2 WIRES, 4-20MA OUTPUT |
|
|
|
|
|
|
|
|
|
|
n |
EXCELLENT STABILITY |
|
|
|
|
|
|
|
n |
HIGH EMI-RFI IMMUNITY |
|
|
|
|
|
|
|
|
|
|
|
n |
CONFIGURABLE BY PC
COMMUNICATOR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
n |
INPUT/OUTPUT ISOLATED |
|
|
|
|
|
|
|
|
|
|
n |
4 DIGIT LED DISPLAY |
|
|
|
|
|
|
|
|
|
n |
3 YEAR WARRANTY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Introduction |
|
|
|
|
Functional Specifications |
|
|
|
IME Model 8080TR is a
Digital, PC programmable, galvanicaly isolated |
|
Sensor |
|
|
|
2-wire smart transmitter.
The unit converts 13 types of thermocouple |
|
|
|
|
|
sensors; 12 types of RTD
sensors, configured as 2, 3 and 4 wires; |
|
13 types of thermocouple;
12 types of RTD, mv, potentionmeter, Ohms |
|
|
potentiometer, resistor
and millivolt inputs into process current loop. A |
|
Calibration Accuracy |
|
|
|
|
24 bit A/D converter is
the heart of this outstanding performance. |
|
|
|
|
|
|
|
+/-0.05%
of span |
|
|
|
|
|
|
Description |
|
|
|
|
Output Signal |
|
|
|
|
IME Model 8080TR
Universal input Smart transmitters are designed for |
|
|
|
|
|
use in process industries
where vibration, inclement weather and corrosive |
4~20mA |
|
|
|
|
|
|
|
atmospheres prevail. The
electronics are enclosed in a copper-free epoxy |
|
Polarity Protection |
|
|
|
coated Aluminum housing
and for more aggressive environments, a |
|
|
|
|
|
SS316 housing is
optionally available. The housings meet the requirements |
Yes |
|
|
|
|
|
|
|
of NEMA 4X, and are also
certified Explosion Proof by FM/CSA. |
|
Isolation |
|
|
|
|
|
|
|
|
|
|
|
1500V AC between input
and output |
|
|
|
|
|
The output current is
temperature linearized and can be set to be 4 to 20 |
|
Burnout Protection |
|
|
|
or 20 to 4mA or any range within
these limits. The current is limited to 3.6 |
|
|
|
|
and 22mA. The unit updates are 3
times per second for the display and 4 |
|
< 3.6mA or >22.1mA
(configurable) |
|
|
|
|
|
times per second (max) for the
current output |
|
|
Supply Voltage |
|
|
|
|
|
|
Exceptional digital
accuracy of typical +/-0.1oC is provided for all the |
|
13~36V DC |
|
|
|
|
|
|
|
sensors regardless of the calibrated
span. Extremely accurate cold-junction |
Operating Temperature |
|
|
|
temperature measurement provides
precise compensation throughout the |
|
|
|
|
|
entire ambient range. The
unit also accurately measures and compensates |
-50~+80oC / -45~+185oF |
|
|
|
|
|
the RTD sensor leads in the 3-wire
connection. The Transmitter can be set |
Weight |
|
|
|
and wired to perform differential
measurement conversions of temperature |
|
|
|
|
|
|
|
sensors as well as mV sources. |
|
|
0.9Kg (2Lb) for Aluminum
unit and 1.4Kg for SS316 Unit |
|
|
|
Material of Construction |
|
|
|
The Transmitter is fully
configurable by connecting to a PC with no external |
|
|
|
|
power supply required.
The configuration parameters are stored in a non |
|
Enclosure epoxy coated
Copper-Free Aluminum or SS316 as specified |
|
|
|
volatile memory. Digital output data
can be obtained via a communication |
|
O Rings |
|
|
|
port located on the front panel.
Continuous, average and max/min readings |
|
|
|
|
can be monitored. |
|
|
Buna N |
|
|
|
|
|
|
|
|
|
Optional Accessories |
|
|
|
Detection of sensor
breakage or disconnection of input leads, forces the |
|
|
|
|
|
output to a pre-defined
up/down scale value. The unit continuously |
|
Mounting Brackets (IME
Model 175PM, 175RC, 175NR, 175MM) |
|
|
monitors the sensor and
automatically returns to normal operation mode |
|
|
|
|
|
when the sensor is recovered. |
|
|
|
|
|
|
|
|
|
|
|
Mounting |
|
|
|
|
|
|
A wide choice of
stainless steel mounting brackets are available for |
|
|
|
mounting the Model 8080TR
on either a 2" pipe or wall. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Metal
Engineering Pte Ltd
http://www.intmet.com |
|
|
|
|
| |
INTERNATIONAL METAL
ENGINEERING |
|
|
|
|
|
|
|
|
|
FIELD MOUNTED 2 WIRE
SMART TRANSMITTER |
|
|
|
8080TR |
|
|
|
SPECIFICATIONS 1 |
|
|
|
|
|
|
Inputs |
|
|
|
|
|
|
|
Input Impedance |
|
>107W |
|
|
|
|
|
|
|
|
|
|
|
|
Maximum Input Voltage |
|
<1V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Thermocouple and
Milivolts |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Type |
Standard |
|
|
Input Range |
|
Minimum Span |
Digital
Accuracy |
D/A |
|
|
|
|
|
|
|
|
oC |
oF |
|
oC / oF |
|
oC |
Accuracy |
|
|
|
|
B
Pt30Rh Pt16Rh |
IEC584-1 ITS-90 |
|
100~1820 |
212~3308 |
|
200 / 360 |
+/- |
0.5 |
|
|
|
|
|
E NiCr-Con |
IEC584-1 ITS-90 |
|
-200~1000 |
-328~1832 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
J Fe-Con |
IEC584-1 ITS-90 |
|
-200~1200 |
-328~2192 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
K
NiCr-Ni |
IEC584-1 ITS-90 |
|
-200~1370 |
-328~2498 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
L
Fe-Con |
IEC584-1 ITS-90 |
|
-190~890 |
-310~1634 |
|
25 / 45 |
+/- |
0.1 |
|
|
|
|
|
N NiCrSi-NiSi |
IEC584-1 ITS-90 |
|
-200~1300 |
-328~2372 |
|
25 / 45 |
+/- |
0.1 |
|
|
|
|
|
R
Pt13Rh-Pt |
IEC584-1 ITS-90 |
|
0~1760 |
-32~3200 |
|
200 / 360 |
+/- |
0.5 |
|
|
|
|
|
S Pt10Rh-Pt |
IEC584-1 ITS-90 |
|
0~1760 |
-32~3200 |
|
200 / 360 |
+/- |
0.5 |
+/- 0.02% |
|
|
|
|
T Cu-Con |
IEC584-1 ITS-90 |
|
-200~400 |
-328~752 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
U
Cu-Con |
IEC584-1 ITS-90 |
|
-190~590 |
-310~1094 |
|
25 / 45 |
+/- |
0.1 |
|
|
|
|
|
D
W3Re-W25Re |
ASTM E988-90 |
|
0~2230 |
32~4046 |
|
25 / 45 |
+/- |
0.5 |
|
|
|
|
|
G
W-W26Re |
ASTM E988-90 |
|
0~2160 |
32~3920 |
|
25 / 45 |
+/- |
0.5 |
|
|
|
|
|
C
W5Re-W26Re |
ASTM E988-90 ITS-90 |
|
-15~2320 |
5~4208 |
|
25 / 45 |
+/- |
0.5 |
|
|
|
|
|
Millivolt
Input |
|
|
-145~145 |
2mV |
+/- |
5mV |
|
|
|
|
|
Mode |
Single or differential sensor |
|
|
|
|
Voltage: ordinary or
differential |
|
|
|
|
|
Cold
Junction |
Intemal Pt-100 Sensor |
|
|
|
|
|
|
|
|
|
C.J
Accuracy |
+/-0.5oC (+/-0.9oF) |
|
|
|
|
|
|
|
|
|
|
|
|
Sampling
Rate |
Single: 10,
differential: 3 (S/sec) |
|
|
|
Voltage: 42,
differential: 4 (S/sec) |
|
|
|
|
|
|
|
Total probable accuracy
for T/C measurement equals to: [C.J.E2+DA2+(Span x 2 x 10-4)2]0.5 |
|
|
|
Where C.J.E is the
cold-junction error and DA is the digital accuracy value for the specific T/C |
|
|
|
Note: For maximum
accuracy for T/C input, all the above error components should be accumulated. |
|
|
|
|
|
|
|
|
|
Resistor Temperature
Detector (RTD) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Type |
Standard |
Input Range |
Minimum Span |
Digital Accuracy |
D/A |
|
|
|
|
|
|
|
oC |
oF |
|
oC / oF |
|
oC |
Accuracy |
|
|
|
|
|
Pt-50 |
|
|
-200~850 |
-328~1562 |
|
200 / 360 |
+/- |
0.5 |
|
|
|
|
|
|
Pt-100 |
IEC-751 |
-200~850 |
-328~1562 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
|
Pt-500 |
a=0.00385W/W |
-200~690 |
-328~1274 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
|
Pt-1000 |
|
|
-200~690 |
-328~1274 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
|
Pt-50 |
|
|
-100~455 |
-148~851 |
|
25 / 45 |
+/- |
0.1 |
|
|
|
|
|
|
Pt-100 |
IEC-751 |
-100~455 |
-148~851 |
|
25 / 45 |
+/- |
0.1 |
|
|
|
|
|
|
Pt-500 |
a=0.00392W/W |
-100~455 |
-148~851 |
|
200 / 360 |
+/- |
0.5 |
|
|
|
|
|
|
Pt-1000 |
|
|
-100~455 |
-148~851 |
|
200 / 360 |
+/- |
0.5 |
+/- 0.02% |
|
|
|
|
|
Ni-Fe |
|
-200~260 |
-328~500 |
|
50 / 90 |
+/- |
0.1 |
|
|
|
|
|
|
Ni-120 |
|
-80~260 |
-112~500 |
|
25 / 45 |
+/- |
0.1 |
|
|
|
|
|
|
Ni-1000 |
|
-50~160 |
-58~320 |
|
25 / 45 |
+/- |
0.5 |
|
|
|
|
|
|
Cu-10 |
|
-120~260 |
-184~500 |
|
25 / 45 |
+/- |
0.5 |
|
|
|
|
|
|
Resistor |
Potentiometer |
0~2KĤ¸ |
|
|
|
|
|
|
|
|
Connection
type |
2, 3 or 4 wire |
|
|
|
|
|
|
|
|
|
|
|
|
Mode |
Single sensor |
|
|
|
Dual-differential |
|
|
|
|
Sensor
Current |
0.3mA |
|
|
|
|
|
|
|
|
|
|
|
Sampling
Rate |
Single sensor; 4
differential; 2 S/sec |
|
|
Potentiometer; 3 S/sec |
|
|
|
|
|
|
|
|
|
|
Example: Pt-100 sensor
input, with a 0~50oC
span: The digital accuracy would be +/- 0.1oC, the accuracy would be +/-50X0.02/100=+/- 0.01oC. |
|
|
Total maximum accuracy=
+/- 0.11oC. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Metal
Engineering Pte Ltd
http://www.intmet.com |
|
|
|
|
| |
INTERNATIONAL METAL
ENGINEERING |
|
|
|
|
|
|
|
|
|
FIELD MOUNTED 2 WIRE
SMART TRANSMITTER |
|
|
|
8080TR |
|
|
|
SPECIFICATIONS 2 |
|
|
|
|
|
|
|
|
Output |
|
|
|
|
|
|
Output Signal |
|
Proportional DC current
4~20mA or 20~4mA (User configurable) |
|
|
|
|
|
|
|
|
Under Range |
|
Linear to 3.97mA |
|
|
|
|
|
|
|
|
|
|
Over Range |
|
Linear to 20.8mA |
|
|
|
|
|
|
|
|
Burnout |
|
<3.6mA or >22.1mA
(User configurable) |
|
|
|
|
|
|
|
|
|
Isolation |
|
>1500V AC between input and
output |
|
|
|
|
|
|
|
Output Linearity |
|
For temperature sensors
- linear with temperature |
|
|
|
|
|
|
|
|
|
|
|
For potentiometer -
linear with potentiometer ratio |
|
|
|
|
|
|
|
|
|
For millivolt input -
linear with the measured voltage |
|
|
|
|
|
|
|
|
Maximum
Loop Resistance |
According to Rmax. (W) = (Vsupply-13)/0.02 |
|
|
|
|
|
|
|
|
|
Calibration
Accuracy |
At 24V supply, at room
temperature: 0.05% of span |
|
|
|
|
|
|
|
|
Damping Factor |
|
1~100 seconds |
|
|
|
|
|
|
|
|
|
|
|
Analog Step-Response |
|
200~500ms (Depends on
the sensor and the mode of operation) |
|
|
|
|
|
|
|
|
Setup Time |
|
5 seconds after power on |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Supply |
|
|
|
|
|
|
|
|
|
|
|
|
Supply Voltage |
|
13~36V DC |
|
|
|
|
|
|
|
|
|
|
|
|
Supply
Variation Effect |
negligible (1mA/V) |
|
|
|
|
|
|
|
|
|
|
Polarity Protection |
|
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
CMR |
|
>110 db |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Environmental Influence |
|
|
|
|
|
|
|
|
|
|
|
Operating
Temperature Range |
-50~+85oC / -122~185oF |
|
|
|
|
|
|
|
|
|
|
|
Temperature Stability |
|
< +/- 0.004% / 1oC |
|
|
|
|
|
|
|
|
|
|
|
Humidity |
|
10%~90%, RH,
non-condensing |
|
|
|
|
|
|
|
|
|
EMC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Programming |
|
|
|
|
|
|
|
Software Package |
|
UstCal |
|
|
|
|
|
|
|
|
|
|
|
|
Modem |
|
IME Model 8080-030,
2-wire Smart Transmitter Config/Debug System with
9-pin D-Type Connector |
|
|
|
|
|
|
|
|
Configured Parameters |
|
Tag
information, Sensor type, Input range, Selection of connection type, Output Offset, Output curve
correction, |
|
|
|
|
|
|
|
|
|
Damping factor, Burnout
Type, Output current mode, Sensor Calibration. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Transmitter Configuration |
|
|
|
|
|
|
|
|
The USTCAL configuration
and calibration software is PC-based software package. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The PC is connected to
the transmitter via MC232 communication cable, which contains the electronic
interface circuitry. This cable which contains |
|
|
|
the electric interface
circuitry. This features makes the configuration process very easy, as it
does not require the transmitter to be wired to an external |
|
|
|
power supply. It is
called "DRY CONFIGURATION".
The Windows based software conducts the user to the configuration steps in a
friendly and |
|
|
|
simple interactive way. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mininum System
Requirement: |
|
|
|
|
|
|
|
|
|
n |
Pentium Processor or
above (Pentium III, 450MHz Recommmand). |
|
|
|
|
|
|
|
|
|
n |
Windows® 95 or above
(Windows XP Professional Recommand). |
|
|
|
|
|
|
|
|
|
n |
64MB RAM or above |
|
|
|
|
|
|
|
|
|
n |
15MB Free Disk Space or
above |
|
|
|
|
|
|
|
|
|
n |
Resolution 800 x 600
(1024 x 768 Recommand) |
|
|
|
|
|
|
|
|
|
n |
CD-ROM 2X or above |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Metal
Engineering Pte Ltd |
http://www.intmet.com |
|
|
|
|
| |
INTERNATIONAL METAL
ENGINEERING |
|
|
|
|
|
|
|
|
|
FIELD MOUNTED 2 WIRE
SMART TRANSMITTER |
|
|
|
8080TR |
|
|
|
Both the Aluminum and
the SS316 housing are certified NEMA 4X. As indicated below. IME Model 8080TR
can be optionally provided with |
|
|
|
certification and a
stainless steel name plate for use in Hazardous Area applications. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ordering Information |
|
|
|
Model |
Description |
|
|
|
|
|
|
|
|
|
|
|
|
8080TR |
Field Mounted 2-Wire
Indicating Transmitter |
|
|
|
|
|
|
|
|
| |
|
|
Code |
Options, Housing |
|
|
|
|
|
|
|
|
|
| |
|
A |
Die cast Aluminum, Epoxy
Coated |
|
|
|
| |
|
T |
SS316, Electro Polished |
|
|
|
|
|
|
|
|
|
| |
|
|
Code |
Instrument Connection
(T1) |
|
Conduit Size (T2) |
|
|
|
|
| |
|
|
01 |
M16 x 2P (See note 1) |
|
|
¾" NPT |
|
|
|
|
|
| |
|
|
02 |
M16 x 2P (See note 1) |
|
|
½" NPT |
|
|
|
|
|
| |
|
|
03 |
M16 x 2P (See note 1) |
|
|
M20 x 1.5P |
|
|
|
|
|
| |
|
|
04 |
½" NPT |
|
|
|
¾" NPT |
|
|
|
|
|
| |
|
|
05 |
½" NPT |
|
|
|
½" NPT |
|
|
|
|
|
| |
|
|
06 |
½" NPT |
|
|
|
M20 x 1.5P |
|
|
|
|
|
| |
|
|
07 |
¾" NPT |
|
|
|
¾" NPT |
|
|
|
|
|
| |
|
|
08 |
¾" NPT |
|
|
|
½" NPT |
|
|
|
|
|
| |
|
|
09 |
¾" NPT |
|
|
|
M20 x 1.5P |
|
|
|
|
|
| |
|
|
10 |
½" BSP |
|
|
|
¾" NPT |
|
|
|
|
|
| |
|
|
11 |
½" BSP |
|
|
|
½" NPT |
|
|
|
|
|
| |
|
|
12 |
½" BSP |
|
|
|
M20 x 1.5P |
|
|
|
|
|
| |
|
|
13 |
¾" NPT |
|
|
|
None |
|
|
|
|
|
| |
|
|
14 |
M20 x 1.5P |
|
|
|
None |
|
|
|
|
|
| |
|
|
16 |
½" BSP |
|
|
|
None |
|
|
|
|
|
| |
|
|
17 |
½" NPT |
|
|
|
None |
|
|
|
|
|
| |
|
|
Code |
Certification |
|
|
|
|
| |
|
NN |
None |
|
|
|
|
|
|
|
|
| |
|
|
Code |
Accessories |
|
|
|
|
|
|
| |
|
|
RC |
IME Model 175RC Mounting
Bracket |
|
|
|
|
| |
|
|
PM |
IME Model 175PM Mounting
Bracket |
|
|
|
|
| |
|
|
NR |
IME Model 175NR Mounting
Bracket |
|
|
|
|
| |
|
|
MM |
IME Model 175MM Mounting
Bracket |
|
|
|
|
| |
|
|
|
|
Code |
2 Inch "U"
Bolt with Nuts and Washers |
|
|
| |
|
|
|
|
00 |
None |
|
|
|
|
|
| |
|
|
|
|
01 |
IME Model 17508, 1 Set
(For IME Model 175RC) |
|
|
| |
|
|
|
|
02 |
IME
Model 17508, 2 Sets (For IME Model 175PM & 175NR) |
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8080TR |
A |
02 |
NN |
PM |
|
02 |
|
Typical
Model Number |
|
|
Note: |
|
|
|
|
1 |
Ports with M16 x 2P
thread are not through holes, they are for Mounting only. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Metal
Engineering Pte Ltd |
http://www.intmet.com |
|
|
|
|
|
|
|
| |
INTERNATIONAL METAL
ENGINEERING |
|
|
|
|
|
|
|
|
|
|
MODEL 175RC MOUNTING
BRACKET |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IME MODEL 175RC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PANEL / WALL MOUNTING
CONFIGURATION |
|
|
|
|
|
|
9 mm or 5/16 bolts for
mounting bracket to wall or panel |
|
|
|
|
|
(Not Supplied) |
|
|
|
|
|
Adaptor P/N: 22305
(Optional) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2Ħħ PIPE MOUNTING
CONFIGURATION |
|
|
|
|
2 Inch "U"
Bolt with Nuts and Wahsers (Optional) |
|
|
|
|
|
|
Adaptor P/N: 22305
(Optional) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
International Metal
Engineering Pte Ltd |
http://www.intmet.com |
|
|
|
|
|
|
|
|
| |
INTERNATIONAL METAL
ENGINEERING |
|
|
|
|
|
|
|
|
|
|
MODEL 175PM MOUNTING
BRACKET |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IME MODEL 175PM |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PANEL / WALL MOUNTING
CONFIGURATION |
|
|
|
|
|
|
|
9 mm or 5/16 bolts for
mounting bracket to wall or panel |
|
|
|
|
|
(Not Supplied) |
|
|
|
|
|
Adaptor P/N: 22306
(Optional) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2Ħħ PIPE MOUNTING
CONFIGURATION |
|
|
|
|
|
|
|
2 Inch "U"
Bolt with Nuts and Wahsers (Optional) |
|
|
|
|
|
|
|
|
Adaptor P/N: 22306
(Optional) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
